Tag Archives: chiller

Four Hop IPA

I brewed up my American IPA with 4 different kinds of C-hops. I tried to do a “regular” brew with a sparge but could not get mash temp above 150 with the original 3.5 gallons. So I ended up with 4.5-5 in the tun. This have me a gravity reading of 1.058 at 140 deg F and 3.75 gallons in the brew pot. I poured 3.5-4 gallons in tun for sparge. I got about 7 total gallons in the brew pot after an hour plus sparge. The gravity was 1.042 at 120+ degrees. This only comes to a gravity of about 1.050, so I’ve decided to do a 90 minute boil. I’ve got far more that 5 gallons in the pot, and I’d like to get a higher gravity. Even though I’m using some whole hops, I don’t think I’ll loose too much.


  • 12# Two-row
  • 0.45# Crystal 40L
  • 0.45# Crystal 60L
  • 0.5# Carapils
  • 1 oz Columbus 13.4% at 60 min
  • 1 oz Centennial 9.3% at 30 min
  • 2 gallon freezer bags full of backyard hops at 15 min
  • 1 oz Cascade 5.5% at 5 min
  • 1 oz Citra (dry-hop in a couple weeks)
Muku looking for a treat.

Too fast for the camera.

When I shook the first package of hops, Muku came looking for a treat. I am still having problems with my wort chiller. I did realize that the connector I purchased last week is slightly off. The 13/16″ male connection has thinner threads than the threads in the female part of the faucet. I switched back to using the out-take spigot from my mash tun and I forced a smaller tube over it, but I still had leakage at the point where it connects to the chiller. After much aggravation, I got the wort chilled, but my 90 minute boil back-fired. While I got a decent OG of 1.064, I only ended up with 4.5 gallons in the fermentor. I pitched California Ale yeast and off it goes.



Leave a comment

Filed under Brewing


Brewed up an amber based on this Irish Red. I have been using this recipe for a while, but I finally managed to find brown malt.


  • 10# two row
  • 0.25# crystal 40L
  • 0.25# crystal 60L
  • 0.25# brown
  • 0.5 carapils
  • 0.75 oz Fuggles for 60 min
  • 0.5 oz Goldings for 60 min
  • 0.25 oz Fuggles at flame out
  • 0.5 oz Goldings at flame out

20160123_150442I got all of the grain and about 7 gallons of water in the mash tun. I am again doing a no-sparge method, but I only mashed for 90 minutes in stead of 3 hours. The gravity reading was about 1.041 with both instruments. About 5 gallons went into the brew pot and 1.5 gallons of heated water went back into the mash tun for a mini-sparge. I stepped out to get an adapter to properly connect my wort chiller to my faucet. I needed a 3/4″ to 13/16″ adapter, I had been having a difficult time finding, but Ace was the place. After a side trip to Brew & Grow for a new fermentor and some DME, I got back home to drain off the mini-sparge which had a gravity reading of about 1.020 at 128 deg F. 20160123_150434I started boiling the main brew pot and the liquid from the mini-sparge separately. After 40 minutes of boiling, I added the remain 1 gallon from the mini-sparge into the main brew pot and added 1# of DME.

Then stuff started to go to hell. I broke the tip off of the floating thermometer. Of course that happened after I went to the brew store. I also again had trouble with the wort chiller. I am now using the correct intake tubing which has a garden hose (3/4″) attachment. The 3/4″ to 13/16″ adapter I bought at Ace fit the tubing to the faucet correctly, but when I turned the faucet on water went everywhere. I eventually minimized the leakage at the connection, but I could not get the tube clamped down tight enough on the chiller to stop dripping at that point. I also tore up my hand trying to tighten up all of the connections, so into the bathtub the brew pot went.

I pitching White Labs Irish ale yeast into 5.5 gallons of wort in the fermentor with an OG of 1.060.

Update: FG was 1.010. Which should give it a 6.5% abv. 20 IBUs


Leave a comment

Filed under Brewing